Some LXD containers on a hidden net, others on your lan

Back in November I wrote about Converting eth0 to br0 and getting all your LXC or LXD onto your LAN

It works, but you might not want ALL of your LXD on your LAN.

You’ll still need your LAN interface to be a br0 instead of a device that isn’t a bridge. Go follow the Bridge your interface section of that post to convert your eth0 to br0.

I’ve fully converted to using LXD. I don’t even remember if LXC supports profiles. I think it does, so I think the same idea could be applied to LXC, but I’m only showing this for LXD.

First, copy the default profile:

lxc profile copy default lanbridge

Second, edit the new profile to use br0 instead of lxdbr0:

lxc profile device set lanbridge eth0 parent br0

Third and finally, start instances with that profile:

lxc launch ubuntu-xenial -p lanbridge

In my case, this instance is on my local lan AND on public ipv6 space (thanks Comcast).

heritable-gale    | RUNNING | 192.168.15.172 (eth0) | 2601:400:8000:5ab3:216:3eff:fe73:d242 (eth0)

 

Converting eth0 to br0 and getting all your LXC or LXD onto your LAN

Wayne has a great post on the new juju lxd work. I’ve been using it a bit and it is awesome. It is super fast and I can create and destroy environments faster than creating and destroying with juju-local.

One thing which I’ve done which has made all LXC and LXD instances more valuable to me, in my home development environment, is to use a bridge to put them directly on my home LAN.

Normally, LXC creates its own device, lxc-br0, which is managed by the lxc-net service. The service creates the device, brings it up, manages the dnsmasq tied to it (which provides DHCP for the 10.0.3.0/24 range).

Bridge your interface

Instead of using lxc-br0, I create a br0. I add my eth0 (and in my case other devices) to that br0. Then I configure LXC and LXD to use br0 instead of lxc-br0. I go as far as stopping the lxc-net service, since I’m not using it.

There is one trick if you are going to do that on a remote home system, e.g. I have an old laptop I leave in the basement and I’m really lazy and I don’t want to walk down there and use its console when I screw up its networking. The trick is to make sure eth0 comes up on br0 when its added there.

Before you do anything, make sure bridge-utils is installed. It probably is if you are already using lxc, but if this is a fresh install, you’ll want to apt-get install bridge-utils

Edit your /etc/network/interfaces and disable eth0 by setting it to manual. Add it to br0 by adding a new br0 section and listing eth0 in bridge-ifaces and bridge-ports.

auto br0
iface br0 inet dhcp
    bridge-ifaces eth0
    bridge-ports eth0
    up ifconfig eth0 up

iface eth0 inet manual

Now run sudo ifup br0. At this point something magical happens, the DHCP lease is renewed but this time the IP address is bound to br0. The magical part is that br0 used the eth0 MAC to make the DHCP request and so you get the same IP address in response and even your SSH session stays open. YAY!

wikipedia network bridge

LXC can use any bridge

Now configure LXC to use this bridge.

apt-get install lxc
sed -i 's/lxc.network.link = lxcbr0/lxc.network.link = br0/' /etc/lxc/default.conf

TADA, now any LXC containers you start with lxc-start will use br0 and get an address from your household DHCP server. They will be accessible from any host in your home.

Now what about LXD?

LXD can use any bridge

It turns out, while LXD is a layer on top of LXC, it doesn’t use /etc/lxc/default.conf for its default config, but instead uses its own settings. These are editable with lxc profile edit default. Change the lxcbr0 in your editor and save and exit. You can check that it is correct by using lxc profile show default.

There you have it. LXD instances starting on your local LAN.

Now go read Wayne’s post again and use the Juju LXD provider.